AV-900 compound venetian blinds with 90 mm-wide, z-shaped slats provide good dimming and individual light regulation. The bold profile allows for a striking façade design. AV-700 compound venetian blinds with 70 mm-wide slats require only a minimum recess depth of 100 mm and allow for a discreet façade design.
Both models are available with rail guidance and guided slats on alternate or both sides, with cable guidance or combined wind-resistant rail and cable guidance.
AV-900 and AV-700
The self-supporting blind system with no mounting in the recess area preserves insulation, reduces noise transmission, and prevents thermal bridges (Minergie standard). A central attachment or a reinforcement profile is required for the head rail from widths of 2500 mm and above.
The flanged holes prevent the 8 mm-wide lift tape from fraying. Not using delicate plastic lugs avoids the need for premature repairs.
The weatherproof chrome steel hooks attaching the slats to the turning cords enable damaged slats to be subsequently replaced. Metal guide bolts ensure durability and resistance to breakage.
Kevlar-reinforced turning cords ensure precise folding without sitting between the slats. This achieves a minimal package height with parallel slat alignment. Dark slat colours can be equipped with black turning cords and lift tapes to prevent them from sticking out.
The bottom rail can be equipped with an end position stop. In the closed end position, this cannot be raised from the outside and thus serves to prevent break-ins.
The innovative textured coating used for the slats demonstrates significantly better colour retention and weather resistance properties than the conventional smooth coating. Dirt adhesion is substantially reduced and the slats are easy to clean.
Both models can be equipped with electric drives, which offer increased comfort. In conjunction with the corresponding controller, this meets the Minergie standard.
The blind can be split into two or three sections with different slat inclines. Open slats in the upper section enable daylight to penetrate into the depths of the room, while closed slats in the lower section serve as glare protection for the window.
Weatherproof chrome steel slat hooks, metal guide bolts, flanged holes for 8mm-wide lift tapes, Kevlar-reinforced turning cords and slats with textured coating all ensure that the blinds will last for a long time.
Choose from around 25 standard colours, including a range of IGP and metallic colours. You can also choose from more than a thousand RAL, NCS and IGP colours.
The slats can either be guided on one side (e.g. for corner windows) or on both sides by filigree chrome steel cables (AV-930 and AV-730 models).
|Height of opening (hl)||Height of recess (hs) AV-900||Height of recess (hs) AV-700|
|to 1750 mm||220 mm||220 mm|
|1751 to 2000 mm||220 mm||240 mm|
|2001 to 2250 mm||235 mm||260 mm|
|2251 to 2500 mm||250 mm||280 mm|
|2501 to 2750 mm||265 mm||300 mm|
|2751 to 3000 mm||280 mm||320 mm|
|3001 to 3250 mm||295 mm||340 mm|
|3251 to 3500 mm||310 mm||365 mm|
|3501 to 3750 mm||330 mm||385 mm|
|3751 to 4000 mm||345 mm||405 mm|
|4001 to 4250 mm||360 mm||425 mm|
|with cover panel||+ 20 mm||+ 20 mm|
|minimum||400 mm||400 mm|
|maximum||4250 mm||4250 mm|
|maximum without warranty||5500 mm||5500 mm|
Width of installation (bk)
|min. with crank drive||345 mm||330 mm|
|min. with motor drive||480 mm||465 mm|
|max./max. without warranty||5000 mm/6000 mm||5000 mm/6000 mm|
Area (bk x hl)
|max. with crank drive||6 m2||6 m2|
|max. with motor drive||10 m2||10 m2|
|max. with crank drive||6 m2||6 m2|
|max. with motor drive||24 m2||24 m2|
|max. coupled blinds||3 pieces||3 pieces|
Depth of recess (tn)
|minimum||130 mm||130 mm|
Wind resistance classes
|bk < 1500 mm||class 6||class 6|
|bk < 2000 mm||class 6||class 6|
|bk < 2500 mm||class 6||class 6|
|bk < 3000 mm||class 5||class 5|
|bk < 3500 mm||class 5||class 5|
|bk < 4000 mm||class 5||class 5|
|bk < 4500 mm||class 4||class 4|
|bk < 5000 mm||class 3||class 3|
AV-900 Download PDF / CAD-File(dwg)
AV-700 Download PDF / CAD-File(dwg)
It is possible that conversion errors occur during saving or importing into another CAD format. Our models are created with the utmost care and the specifications are checked for accuracy. However, we cannot assume liability for possibly faulty or incomplete specifications as well as the correct depiction of the product in your CAD system. We recommend checking all relevant installation dimensions according to the information from our brochure pages.
checking all relevant installation dimensions according to the information from our brochure pages.